Donate with PayPal to help keep UKS online!



Go Back   UKScrappers > Forum > Special Forums > Cutting Machines - chat, help. templates > Cutting Machine Chat

Notices


Results 1 to 9 of 9

Thread: Tips needed

  1. #1
    You are my inspiration............ shazzer's Avatar
    Join Date
    Mar 2003
    Location
    Herstmonceux, East Sussex
    Posts
    154
    View Gallery

    Trader Rating: (9)

    Tips needed

    Hi Everyone
    Just treated myself to the Cameo 3 and I think I've got to grips with the design studio bit of it! Well as much as I need to ofr now anyway.
    What I want to know is how does everyone stop their mat from being so sticky? Mine is horrendous.
    TIA

    Sharon

    I'm a Scraphazard Sinner with a Heart of Gold, whose a Christmas Cracker
    Proud owner of a new Silhouette Cameo 3 who needs a helping hand

  2. #2
    You are my inspiration............ shazzer's Avatar
    Join Date
    Mar 2003
    Location
    Herstmonceux, East Sussex
    Posts
    154
    View Gallery

    Trader Rating: (9)
    Also, if cutting Vinyl should it cut through the backing paper as well?

    I'm a Scraphazard Sinner with a Heart of Gold, whose a Christmas Cracker
    Proud owner of a new Silhouette Cameo 3 who needs a helping hand

  3. #3
    Dedicated Scrapper
    Join Date
    Feb 2011
    Location
    East Sussex
    Posts
    867
    View Gallery

    Trader Rating: (0)
    Quote Originally Posted by shazzer View Post
    Also, if cutting Vinyl should it cut through the backing paper as well?
    No it should not cut through the back at all. It should only kiss cut the vinyl.
    To make mat less sticky use a lint free piece of cloth and keep dabbing on the mat until it feels less sticky. Make sure it is lint free though or you will end up with bits of fluff stuck all over the mat.

  4. #4
    Graphtec GB BrianP's Avatar
    Join Date
    Jun 2008
    Location
    Wrexham
    Posts
    431
    View Gallery

    Trader Rating: (0)
    If you are cutting through the backing of vinyl you need to reduce your blade settings and/or your thickness settings. A blade of 1, thickness 7-12 and speed 10 are normally best suited for vinyls but you can often need to reduce the thickness lower of very thin vinyl.

    As for the mat, some people say they find the mats too sticky, some say they are not sticky enough, it really depends on the media you are using. The thinner the media the less sticky you want your mat. If you only use thin materials you may be better using the low tack mats.
    Technical Support
    Graphtec GB
    www.graphtecgb.co.uk

  5. #5
    You are my inspiration............ shazzer's Avatar
    Join Date
    Mar 2003
    Location
    Herstmonceux, East Sussex
    Posts
    154
    View Gallery

    Trader Rating: (9)
    Thank you for your replies. However the Cameo 3 has an auto blade, how do i adjust it?

    I'm a Scraphazard Sinner with a Heart of Gold, whose a Christmas Cracker
    Proud owner of a new Silhouette Cameo 3 who needs a helping hand

  6. #6
    Graphtec GB BrianP's Avatar
    Join Date
    Jun 2008
    Location
    Wrexham
    Posts
    431
    View Gallery

    Trader Rating: (0)
    Quote Originally Posted by shazzer View Post
    Thank you for your replies. However the Cameo 3 has an auto blade, how do i adjust it?
    The auto blade sets itself to the settings in the cut preset you choose. So you'd need to create a new preset with the settings above and then try a test cut.

    If you can tell me which version of Silhouette Studio you're using I can tell you the steps needed to create a new preset. The steps vary between versions, so I'd need to know the version so I get the steps correct.
    Technical Support
    Graphtec GB
    www.graphtecgb.co.uk

  7. #7
    You are my inspiration............ shazzer's Avatar
    Join Date
    Mar 2003
    Location
    Herstmonceux, East Sussex
    Posts
    154
    View Gallery

    Trader Rating: (9)
    Quote Originally Posted by BrianP View Post
    The auto blade sets itself to the settings in the cut preset you choose. So you'd need to create a new preset with the settings above and then try a test cut.

    If you can tell me which version of Silhouette Studio you're using I can tell you the steps needed to create a new preset. The steps vary between versions, so I'd need to know the version so I get the steps correct.
    Hi Brian, I'm using Silhouette Studio 4.0

    I'm a Scraphazard Sinner with a Heart of Gold, whose a Christmas Cracker
    Proud owner of a new Silhouette Cameo 3 who needs a helping hand

  8. #8
    Graphtec GB BrianP's Avatar
    Join Date
    Jun 2008
    Location
    Wrexham
    Posts
    431
    View Gallery

    Trader Rating: (0)
    On v4 you click the SEND tab, and then click the 'Add new material type button' as shown below:

    add_mat_1.png

    Next you give the material a name (e.g. My_Vinyl), then click the down arrow next to 'Add Action' and select 'Add Cut Action'.

    After this you then set the settings as shown in the screenshot below:

    add_mat_2.png

    Once the speed, blade and thickness settings are set you press 'Save' and then you make sure you select this preset when cutting this material.

    Those settings might not be exact for your vinyl, as it is hard for me to be exact without having that media here to test, so you may need to tweak the settings a little and use the 'Test Cut' button to see if it works for you, but this should at least give you the info you need to make your own presets in v4.

    If you find it hard to see the screenshots I've attached, try right-clicking on them and select 'open in new tab' to open them full sized.
    Last edited by BrianP; 25-05-2017 at 12:28 PM.
    Technical Support
    Graphtec GB
    www.graphtecgb.co.uk

  9. #9
    You are my inspiration............ shazzer's Avatar
    Join Date
    Mar 2003
    Location
    Herstmonceux, East Sussex
    Posts
    154
    View Gallery

    Trader Rating: (9)
    Hi Brian
    Thank you so much. It is actually a Vinyl from the Graphtec bumper pack that I bought from C&C with my machine.

    I'm a Scraphazard Sinner with a Heart of Gold, whose a Christmas Cracker
    Proud owner of a new Silhouette Cameo 3 who needs a helping hand

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Click HERE for additional Sponsors


All times are GMT +1. The time now is 02:13 PM.